Menu
Ultra Series Natural Stone

Ultra Series Natural Stone

Zero Gloss + Color Enhancer

Water-Based sealer for natural stone products

Description

Ultra Seal for Natural Stone is made of silicone based polymers. This sealer penetrates deep into the natural stone thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt.

Features

  • Vibrant color enhancer
  • Apply on dry surface only
  • Rain-safe after 24 hours
  • Non film-former
  • Easier to clean and maintain
  • Works at above 40ºF (4°C)
  • For use on salt water pool patio areas
  • Water-based, zero gloss

Helps Resist

  • Corrosion from de-icing salt
  • Ultraviolet rays effects
  • Motor oil and grease stains

Application & Installation

FOR NATURAL STONES:

  1. ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations.
  2. Remove all the stains from the natural stones, using Flexlock Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the natural stone surface.
  3. Remove all contaminated jointing material and replace with Flexlock Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation.
  4. Wait at least 48 hours at a minimum temperature of 40°F (4°C) and no rain for the Flexlock Polymeric Sand to properly harden.
  5. Clean the entire surface with the Flexlock Efflorescence Cleaner. This product will remove the efflorescence trapped in the natural stone pores as well as thoroughly clean the surface for proper sealer adhesion.
  6. Wait at least 48 hours at a minimum temperature of 40°F (4°C) and no rain so the sand & natural stone surface are dry.
  7. Best Practice: (See online video. 2 people needed.) Apply one (1) coat of Ultra Series Natural Stone Sealer using a sprayer in 60 sq. ft. sections, then use a solvent-resistant foam roller to remove the excess sealer left on the surface.
  8. Ultra Series Natural Stone Sealer is water repellant, rain safe, after 24 hours.
  9. Let the sealer dry for 24 hours before using the sealed area.

PLEASE NOTE:

  1. Natural stones should only be sealed 60 days after their installation date. Consult natural stone manufacturer’s for their recommendation.
  2. Natural stones and jointing sand MUST be 100% dry.
  3. Temperature should be between 40°F (4°C) and 85°F (29°C) when sealer is applied.
  4. Natural stone surface must be cool to the touch when sealer is applied (between 40°F (4°C) and 85°F (29°C)).
  5. First clean natural stones with Flexlock Clean products. Remove all oil, grease and rust stains.
  6. Use Flexlock Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion.
  7. Use just one (1) layer of sealer.
  8. When using Ultra Series Natural Stone Sealer, assure yourself at least 48 hours of dry conditions prior to applying the sealer.
  9. Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer.
  10. Wear protective gloves, eye protection and respiratory protection.

Coating Category: Waterproofing Concrete/Masonry Sealers. VOC Concentration Limits: <100 g/L (grams of VOC per liter of coating, less water and less exempt compounds). SCAQMD compliant.

Coverage

Products Area
Granite 400-600 sq. ft. per gallon
Travertine 500-700 sq. ft. per gallon
Limestone 300-500 sq. ft. per gallon
Sandstone 200-400 sq. ft. per gallon
Bluestone 200-400 sq. ft. per gallon

*Coverages are approximate and will vary based on stone porosity, joint width and other factors.

Packaging

Products Retail Size Per Box Per Pallet
Ultra Series Natural Stone 3.78 L. (1 U.S. gal.) 4 units 24 boxes
Ultra Series Natural Stone 18.9 L. (5 U.S. gal.) 0 units 48 pails

Limited warranty

Before applying the product, the user/buyer must determine its suitability for intended use and user/buyer assumes all risks in that regard. It is a condition of the Limited Warranty that before using the product on the intended larger area, the user/buyer must first test the product on a small less observed area of approximately 4 sq. ft. (0.4 sq. m.) to ensure results meet user/buyer’s expectations. In the event that no test is carried out, the Limited Warranty will only apply to 4 sq. ft. (0.4 sq. m.). ALLIANCE DESIGNER PRODUCTS INC. cannot guarantee results as it has no control over surface preparation and product application.

If this product is proven to be defective, on the condition that it was applied pursuant to the required method of application and surface preparation, the sole obligation ALLIANCE DESIGNER PRODUCTS INC. is to refund the purchase price. Proof of purchase is required for any claim. ALLIANCE DESIGNER PRODUCTS INC. shall not be liable for any other damages whatsoever, direct or consequential. To the extent permitted by law, ALLIANCE DESIGNER PRODUCTS INC. excludes any implied warranty of quality, merchantability or fitness for purpose. The container must at all times be stored at above 32°F (0°C) and away from direct sun to receive the benefit under the Limited Warranty.