For joints up to 4” (10 cm) in traditional applications
and 2” (5 cm) in overlay applications
NO DUST • HAZE FREE • NO BLOWER • ONE WATERING
RAIN SAFE IN 15 MINUTES
FLEXLOCK ULTRA SAND G2 is made with a state-of-the-art manufacturing process. Specifically, calibrated sand is mixed with sophisticated intelligent polymers. This new generation of Intelligent Polymers neutralizes haze and dust. The polymeric sand application is now dust free and haze free. No blower is needed and the intelligent polymeric sand requires only one watering. FLEXLOCK ULTRA SAND G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. Available in Beige, Slate Grey, Ivory and Black Diamond.
Maintenance of paved surface
When maintaining the paver surface, apply Gator Shampoo to clean the entire paved surface including the paver joints. Wash, rinse and remove any residue by using a hose and a watering gun set to shower with the normal maximum water pressure from any residential or commercial building (typically 80 psi/550 kPa).
Moss
FLEXLOCK ULTRA SAND G2 will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on-site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product.
Clay Pavers
If used on clay pavers make sure they are 100% dry. Clay pavers tend to hold moisture, which can prematurely activate the FLEXLOCK ULTRA SAND G2 while the sand is being spread over the paver surface, leaving a residue. Always apply on a test area before using the FLEXLOCK ULTRA SAND G2 on clay pavers.
Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints.
| Per 50 lb (22.7 kg) bag (Paver 2-3/8” (6 cm) in height) | NARROW JOINTS 1/8″ to 3/8″ (3-9 mm) | WIDE JOINTS 3/4″ to 1-1/4″ (19-32 mm) |
|---|---|---|
| Beige, Slate Grey, Ivory | 65-85 sq. ft. (6-7.4 sq. m.) | 22-42 sq. ft. (2-3.9 sq. m.) |
| Black Diamond | 58-76 sq. ft. (5.5-6.5 sq. m.) | 20-38 sq. ft. (1.8-3.5 sq. m.) |
| Product | Size | Units per Pallet |
|---|---|---|
| FLEXLOCK ULTRA SAND G2 – Beige | 50 lb (22.7 kg) | 56 |
| FLEXLOCK ULTRA SAND G2 – Slate Grey | 50 lb (22.7 kg) | 56 |
| FLEXLOCK ULTRA SAND G2 – Ivory | 50 lb (22.7 kg) | 56 |
| FLEXLOCK ULTRA SAND G2 – Black Diamond | 50 lb (22.7 kg) | 56 |
PLEASE NOTE:
All pavers must be completely interlocked for vehicular and pedestrian use. If pavers are fanned they are not considered interlocked. FLEXLOCK ULTRA SAND G2 can be applied when pavers are installed directly open graded aggregates that lock or choke themselves. This means the polymeric sand will not migrate through the voids. Do not apply FLEXLOCK ULTRA SAND G2 when the pavers are installed directly on aggregates with large voids.
Maximum joint width for overlays: 2″ (5 cm)
Maximum joint width for traditional base: 4″ (10 cm)
POLYMERIC SAND REQUIREMENTS
Minimum joint width: 1/8″ (3 mm)
Maximum joint width: 4″ (10 cm)
Maximum overlay joint width: 2″ (5 cm)
Minimum joint depth: 1 1/2″ (38 mm)
FLEXLOCK ULTRA SAND G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a traditional or overlay base system. (See diagrams).
C-33 sand or ASTM No. 9 stone can be used under pavers as a bedding layer.
C-33 sand or ASTM No. 9 stone can be used under pavers.
Note:
C-33 sand or ASTM No. 9 stone can be used under pavers.
Note:
C-33 sand or ASTM No. 9 stone can be used under pavers.
1
2
Sweep & Vibrate G2 Intelligent Polymeric Sand
3
Sweep off excess G2 Intelligent Polymeric Sand
4
Activate G2 Intelligent Polymeric Sand with water
1
2
Sweep & Vibrate G2 Intelligent Polymeric Sand
3
Sweep off excess G2 Intelligent Polymeric Sand
4
Activate G2 Intelligent Polymeric Sand with water
Spread with hard-bristle broom. Make sure the FLEXLOCK ULTRA SAND G2 completely fills the joints. Do not use with other materials in the joints. Leave a layer of FLEXLOCK ULTRA SAND G2 on the surface to aid in the vibrating and consolidation of FLEXLOCK ULTRA SAND G2 into joints. For textured or pre-finished surfaces, we recommend to remove all the sand from the paver or slab surface prior to using the plate or roller compactor.
Vibrate the FLEXLOCK ULTRA SAND G2 into the paver joints using a vibratory plate compactor. A rubber pad is recommended. A roller compactor is best for slab installation. Joints sand level, must be at least 1/8 inch (3 mm) below top of paver’s surface without chamfer or 1/8 inch (3 mm) below the chamfer. It is best to compact in several directions to ensure there are no air gaps or voids in the joints. Repeat steps 1 and 2 to ensure joints are filled and consolidated. Narrow joints require more care to completely fill.
Sweep off excess FLEXLOCK ULTRA SAND G2 from the paved surface, first with a hard-bristle broom, then a soft-bristle broom. Take care to leave the height of FLEXLOCK ULTRA SAND G2 at least 1/8 inch (3 mm) below top of paver’s surface without chamfer or 1/8 inch (3 mm) below the chamfer
Shower for a minimum of 30 seconds for 30 sq. ft. (3 sq. m.) or until the FLEXLOCK ULTRA SAND G2 repels the water and the water starts to accumulate on the joints.
Remove existing jointing material. Be careful not to disturb the bedding material under the pavers. Pavers must be completely dry before installing a minimum of 1 1/2’’ (38 mm) deep into the joints. FLEXLOCK ULTRA SAND G2 level, must be at least 1/8 inch (3 mm) below top of paver’s surface without chamfer or 1/8 inch (3 mm) below the chamfer or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires. Follow FLEXLOCK ULTRA SAND G2 installation steps 1 to 4 for a new paver surface.
Please note that this limited warranty applies only when the product is used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use). The manufacturer cannot guarantee results as it has no control over surface and sub-surface preparation and product application. (Proper installation of pavers or slabs to ensure long-term stability of work, including granular foundation of certified crushed stone of 0-3/4″ (0-20 mm) (minimum of 6″ (15 cm)), bedding sand layer (maximum of 1″ (25 mm)) and appropriate installation of reinforced edging in accordance with above specified method for applying product.) Also warranted when used with Gator Base. However, for a period of 15 years from purchase, the manufacturer agrees that if the product is proven to be defective, and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above, then the manufacturer agrees to refund the purchase price. Proof of purchase is required for any claim.
THE PARTIES AGREE THAT REFUND OF THE PURCHASE PRICE AS STATED IS THE ONLY OBLIGATION OF THE MANUFACTURER. IN ALL EVENTS, THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES OR COSTS WHATSOEVER, (INCLUDING REMOVAL OR REINSTALLATION OF SAND OR PAVERS) DIRECT OR CONSEQUENTIAL. TO THE EXTENT PERMITTED BY LAW, THE MANUFACTURER EXCLUDES ANY IMPLIED WARRANTY OF QUALITY, MERCHANTABILITY OR FITNESS FOR PURPOSE. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility whatsoever for the presence of moss, mold, mildew, or similar factors that may occur on the product after its installation. The presence of moss, mold or mildew is caused by the particular on-site conditions, including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product after installation. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of FLEXLOCK ULTRA SAND G2 for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10.
Please note that when the product is used for other purposes (Mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from purchase. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of any Polymeric Sand for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10.
Jeudi 21 Mars
1 : 00 PM
Mercredi 20 Mars
1 : 00 PM
